![]() To do so, you can use a shell provisioner script:Ĭonfig.vm.network "public_network", ip: "192.168.0.17" This is required if you need access the Vagrant box from other networks over the public network. But you can override the default router configuration for eth1.ĭepending on your setup, you may wish to manually override the default router configuration. If I immediately do a vagrant up again, it has re-enabled the NAT adaptor again, and we're back to having the same problem again.Įth0 as NAT is a fundamental requirement of Vagrant in its current state. VBoxManage: error: Context: "AddRedirect(Bstr(strName).raw(), proto, Bstr(strHostIp).raw(), RTStrToUInt16(strHostPort), Bstr(strGuestIp).raw(), RTStrToUInt16(strGuestPort))" at line 1655 of file VBoxManageModifyVM.cpp VBoxManage: error: Details: code NS_ERROR_INVALID_ARG (0x80070057), component NATEngine, interface INATEngine, callee nsISupports Stderr: VBoxManage: error: A NAT rule of this name already exists The command and stderr is shown below.Ĭommand: There was an error while executing `VBoxManage`, a CLI used by Vagrantįor controlling VirtualBox. If I try and vagrant up the box after editing the VirtualBox settings and disabling the NAT adaptor, I get the following error: If I edit the VirtualBox settings and disable the NAT adaptor, so there is only the bridged Adaptor and boot up the box via VirtualBox (ie: not using vagrant up), then it only has eth0 with a IP address that is pingable from my devbox, which is what I'm looking for. ![]() How do I get rid of the NAT adaptor and use bridged only? You can also, when it boots up, it does a port forward on Adaptor 1, which is the NAT adaptor, which means it sounds like it's using the NAT adaptor by default for everything. As you can see, there are two IP addresses for the Vagrant VM, which doesn't seem right. The Virtual machine setups they have is with a Bridged NIC only, but the vagrant for some reason has both a NAT and Bridged, even though, I've specified bridged in the config. My problem is that, that I can ping the VM from my host machine ( IP: 10.0.24.112), other people can ping my my VM too ( 10.0.24.XXX), my VM can ping my devbox ( IP: 10.10.116.254), I can ping other developers virtual machine setups from my devbox (not Vagrant, IP: 10.10.116.254), but I can't ping my VM from my devbox and other developer's can't ping my VM from their devbox. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 ![]() RX packets:3490 errors:0 dropped:0 overruns:0 frame:0 TX packets:544 errors:0 dropped:0 overruns:0 carrier:0 RX packets:725 errors:0 dropped:0 overruns:0 frame:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Provisioners marked to run always will still run.Įth0 Link encap:Ethernet HWaddr 08:00:27:88:0c:a6 Run `vagrant provision` or use the `-provision` => default: Configuring and enabling network interfaces.ĭefault: /vagrant => /Users/garthm/Projects/vagrant ![]() => default: Checking for guest additions in VM. This may take a few minutes.ĭefault: Warning: Connection timeout. => default: Preparing network interfaces based on configuration. => default: Clearing any previously set network interfaces. => default: Clearing any previously set forwarded ports. => default: Checking if box 'hashicorp/precise64' is up to date. => default: Attempting graceful shutdown of VM. nfigure(VAGRANTFILE_API_VERSION) do |config|Ĭonfig.vm.network "public_network", type: "dhcp", :bridge => 'en4: Thunderbolt Ethernet' So I'm having an issues with a Vagrant setup of 'hashicorp/precise64' on my MAC book.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |